Shopping Cart

Shipping Estimate

Applies to this product only
Country:
Region / State:
Post Code:
Ames Maximum Stretch Elastomeric 3.78 Litre

Ames Maximum Stretch Elastomeric 3.78 Litre

  • $108.99

Available Options

Preparation

Surface has to be in savable condition, clean and dry with proper drainage. Pressure wash when possible using pure water. Be sure the surface is clean and completely dry before the application of the coating. Read all label instructions before beginning. Always run a test patch first in an inconspicuous area, to ensure that proper adhesion and drying occurs and the product works to your satisfaction. As an option, use Ames’® Peel & Stick™ adhesive seam tape and tape all joints, seams and around vents. Do not use any soaps or detergents to clean the surface. Call for specific instructions 888-345-0809.

 

General Application:

Pour the thick liquid coating out and spread 1-2 gallons of product liberally with a push roller or broom. Work the product until it is smooth and looks consistent in thickness. Move on after a few minutes so the product does not skin over or form a film which can create an unintended texture in the coating’s finished appearance. In most instances, the minimum application is two coats at a rate of one gallon per 100 sq. ft. per coat.

 

Tools:

Ames’® Maximum-Stretch™ can be applied with a paint brush, a push broom, a low nap roller with a long handle or a Commercial Airless Sprayer.  In addition, you may need Ames® Peel & Stick Seam Tape and scissors or a utility knife.  For larger commercial jobs, we recommend a commercial/industrial airless sprayer.  Call toll free for sprayer specifications and information at 1-888-345-0809.

 

Estimated Coverage:

Standard product coverage on a smooth surface is 100 sq. ft. per gallon per coat. Rough or uneven surfaces may require additional product. More than one coat is recommended. More coats equal longer life.

 

Weather & Drying Guidelines:

Ames’® Maximum-Stretch™  is best applied between 50° to 90° F (10° to 32° C) on warm and dry surfaces. Apply when the streets are dry, the sun is in the sky and no inclement weather is forecast. Starts to dry in about 2-8 hours, depending on thickness of application and weather; if at all possible, for best results, we recommend a minimum of 24 hours between coats. No rain in the forecast and no freezing temperatures. Low temperatures, high humidity and evening and morning dew will require increased drying/curing time. Do not apply after 3pm for best drying. The earlier you can put it on, the better. Make sure any morning dew is completely dried off before proceeding.

 

Clean-up, Storage, and Disposal:

Clean tools and small spills with water. Store unused product in its original container, tightly sealed and protect from freezing. Dispose of this product in accordance with local, state, or federal requirements.

 

 

Application by Roof Type

 

Metal Roofs, including:  Tin, Aluminum, Rusty Metal, Corrugated Metal, Butler Buildings, Hangers and Factories:  Residential & Commercial

Use Ames’® Peel & Stick™ adhesive seam tape and tape all joints, seams, cracks, splits, transitions and around any vents or units you may have. In order for the tape to work properly it has to be on a smooth surface. You may also use Ames’® Super Primer™ over any rust to help with possible bleed through. For best adhesion, use Ames’® Super Primer™ over any silver aluminum fibrous coating.  Top coat with a minimum two coats of Ames’® Maximum-Stretch™ at a rate of one gallon per 100 sq. ft. per coat.

 

Flat Roofs, including: Tar & Gravel Roofs, Built up Tar Roofs, And Aluminum Coated Roofs:  Residential & Commercial

For best results, the water must run off completely with no ponding.  Install adequate drains where needed as flat roofs must be properly drained.  Prime the roof with a minimum of two gallons per 100 square feet of Ames’® Super Elasto-Barrier™ liquid rubber - coating liberally to fill in the cracks and to seal the roof. Once dried, then top coat with a minimum of two gallons per 100 square feet of Ames’® Maximum-Stretch™.  Rough or uneven surfaces may require additional product. Ames Contouring Roof Fabric and Ames Peel & Stick Seam Tape are optional. NOTE:  Do not apply fabric over a tar and gravel roof.  Call for specific details.

 

Pitched Rolled Roofing: Residential & Commercial

Coat with Ames’® Super Elasto-Barrier™ at the rate of a minimum of two gallons per 100 square feet.  Once dried, then top coat with a minimum of two gallons per 100 square feet of Ames’® Maximum-Stretch™.  For future and simple maintenance of roof, just add Ames’® Maximum-Stretch™ applied at a minimum of one gallon per 100 square feet per coat. Ames Contouring Roof Fabric and Ames Peel & Stick Seam Tape are optional. Call for specific details.

 

EPDM/Rubber, TPO, PVC, Concrete and White Vinyl Roofs: Residential & Commercial

Power wash clean and make sure surface is completely dry.  Apply one coat of Ames’® Super Primer™ at the rate of one gallon per 200 square feet per coat. The Super Primer will go on milky white and will dry clear. Make sure it is completely clear before you proceed. (approx. 30 min. to one hour) Apply Ames’® PS250 for any seams, cracks, splits, transitions or around any vents or units you may have. In order for the tape to work properly it has to be on a smooth surface. For the best application, apply a minimum of two coats of Ames Super Elasto-Barrier™ at a rate of one gallon per 100 sq. feet. Work the product until it is smooth and looks consistent in thickness.  Finish the application with two coats of Ames’® Maximum-Stretch™ at the rate of a minimum of one gallon per 100 square feet for a highly reflective energy saving roof system. Ames Contouring Roof Fabric and Ames Peel & Stick Seam Tape are optional. Call for specific details.

 

Reflective and Maintenance Coating Applications:

For preventative maintenance and longevity only - Apply Ames’® Maximum-Stretch™ at a rate of one to two gallons per 100 square feet.  Ames’® Maximum-Stretch™ is quality rubber and acrylic that seals, stretches, long lasting and reflects the UV up to 98%. Rubber and concrete roofs must be primed first with Ames Super Primer to create an adhesive surface. 

 

Can be used in Conjunction with: 

Ames® Peel and Stick Contouring Seam Tape
Ames® Super Elasto-Barrier
Ames® Super Primer
Ames® Contouring Roof Fabric



Estimated 100 Square Feet per Gallon

Ames® Maximum-Stretch™ is a thick, high quality rubber and acrylic elastomeric coating designed specifically for waterproofing, repairing and maintaining many different types of roofs. Temperature fluctuations and severe weather will cause tremendous expansion and contraction of roofs which loosens up the building over time causing roofs to fail and leak. Ames’® Maximum-Stretch™ has remarkable adhesion and is easy to apply. It dries rapidly to form a cool white, watertight roof membrane with up to 750% elasticity that expands and contracts with the roof surface. Ames’® Maximum-Stretch™ stays cool and resists cracking and peeling. It reflects up to 98% of the sun’s rays to reduce roof temperature and energy costs. Ames’® Maximum-Stretch™ remains flexible at freezing temperatures. It has been developed for a wide range of climates from hot to cold, and formulated to resist fungus, mold and mildew. Available in three colors of white, tan and light grey at no additional charge.  Maximum Stretch can also be tinted to a limited selection of pastel colors.

Write a review

Note: HTML is not translated!
    Bad           Good